新增網頁1

Electrical Fan Plant Page: 1. 2. Up Index

Product Name: Air cooled heavy-duty reciprocating air compressor

Description:

Continuous running unloader
For continuous-running air compressors, unloader lets unit idle load-free until air supply drops to cut-in pressure; automatically lets unit idle again after high pressure limit is reached. (Tubing and fittings not included on bare compressor).
Valve assembly
All units use large disc-type valves made from Swedish steel for high efficiency and long wear.
Suction strainer
Permanent type strainer effectively filters air and muffles noise of air intake. Easily removed for periodic cleaning.
Cool cylinder heads
Deep directional fins provide quick cooling; compact streamlined air passages in the cylinder head permit fast, efficient flow of cooler intake air and rapid removal of discharge air.
Long-life cylinders
Precision-machined cylinder walls are honed glass-smooth to reduce friction and wear to a minimum. Extra-deep fins provide increased cooling and greater strength.
Rings
Long life industrial design compression and oil control rings are used to assure maximum performance.
Connecting rods
All units contain precision bored, industrial quality designed connecting rods...a splash lubrication is used.
Balanced Crankshafts
Made from a high-tensile forged alloy steel, precisely ground and dynamically balanced to insure long life and smooth operation. Journals are ground precisely to extend bearing life.
Crankcase
The extra large crankcase with big oil reservoir assures cooler running and better lubrication.
Balanced fan-type flywheel
Airfoil-type spokes provide a continuous powerful blast of cooling air for all portions of the compressors; balancing assures smooth vibration-less operation.
Main bearings
To ensure long life and easy maintenance, high quality ball bearings or tapered roller bearings are used in the Fu Sheng compressors.
Easy oil check
The oil level check is in a convenient location for "tell at a glance" reading of oil level in crankcase.

Specification:

A-Series Single-Stage Specifications

Model

HP

# Cyl.

Piston Disp.

Actual Air Delivery

Maximum
Pressure

5kg/cm²G (70PSIG)

7kg/cm²G (100PSIG)

Liters/Min

CFM

Liters/Min

CFM

Liters/Min

CFM

kg/cm²G

PSIG

CA-51

0.25

1

55

1.94

34.7

1.22

30.8

1.08

10

140

CA-65

0.5

1

102

3.6

64.2

2.26

57.1

2.01

10

140

VA-51

0.5

2

106

3.74

66.8

2.35

59.4

2.09

10

140

VA-65

1

2

185

6.54

125.8

4.44

116.5

4.12

10

140

TA-65

2

3

303

10.7

206

7.27

190.9

6.74

10

140

VA-80

3

2

462

16.3

340

12

310

11

10

140

TA-80

5

3

767

27.1

540

19.1

510

18

10

140

VA-100

7.5

2

1045

36.9

710.6

25.1

658.4

23.3

10

140

TA-100

10

3

1484

52.4

1009

35.7

934.9

33

10

140

TA-120

15

3

2334

82.5

1591

56.2

1474

52.1

10

140

　

A-Series Single-Stage Dimensions (metrics)

Model	Basic Compressor				Complete Compressor
	Height	Length	Depth	Weight	Tank Capacity	Height	Length	Depth	Weight
	mm	mm	mm	kg	liter	mm	mm	mm	kg
CA-51	273	173	182	7.8	28	605	650	306	28
CA-65	331	270	222	14.2	28	666	650	306	42
VA-51	257	310	228	13.8	60	685	910	385	50
VA-65	317	370	275	20.5	70	747	1050	385	63
TA-65	357	466	320	27.2	70	874	1050	460	70
VA-80	404	530	380	48	105	1000	1160	480	116
TA-80	470	592	426	67.5	155	1177	1410	588	160
VA-100	490	586	475	93.5	245	1177	1440	588	263
TA-100	550	660	510	121	304	1227	1770	640	344
TA-120	660	810	580	182	304	1345	1770	665	405
Note: Weight of complete compressor does not include motor.

　

Product Name: Screw Air Compressor

Description:

Internationally patented rotor profile results in energy saving and low running cost
Asymmetric rotor profile with 5-lobe male and 6-flute female rotors leads to low backflow due to small differential pressure between flutes. Thus, the adiabatic efficiency increases by 10~12% and energy savings by 25% as compared to the 4 to 6 profile design.
Precisely machining equipment leads to high precision of products
Adopting the most advanced machining facility when processing components of compressors to match the requirement of high precision.
Bearings of long service life and low noise level
A bearing designed life of 50,000 hours is assured thanks to the high precision machining and excellent dynamic balance on specially designed short rotors which minimize vibration and bending stress. Furthermore, the low revolution of rotors reduced noise level.

For Those Concerned About the Quality...

Hi-Tech Microprocessor

Based on CMOS design, high resistance to noise signals and low power consumption can be achieved. The microprocessor integrated modulation valve, maintenance indicators, protection devices and auto stop function into a reliable control system.

Cooler

Low temperature difference design of coolers is suitable to be used in all kinds of circumstances.

Suction valve

Simplified design enables the suction valves to have a long service life (SA-110A II and SA-115A II).

Modulation suction valve

The reliable design can precisely control the delivery of compressed air to reduce horsepower consumption and save energy (SA-220A II ~ SA-350A II)

Oil filter

To remove alien particles in oil, e.g. metal particles. Protect revolution mechanisms from damage.

Oil fine separator

Oil fine separator controls oil content under 3ppm. Excellent separation extends the service life of compressors.

No trouble to change the element of separator results in time savings.

Specification:

Model	Stage	Air Delivery	Hp	Voltage	Dimension
					Length	Width	Height	Weight
		(m³/min)			^(mm)	^(mm)	^(mm)	^(kg)
^{SA-110A II}	^SA-1	^1.1	¹⁰	^{220/ 380/ 440}	¹¹⁸⁴	⁷⁶⁰	¹³⁵⁰	⁴⁵⁰
^{SA-115A II}		^1.6	¹⁵					⁴⁷⁵
^{SA-220A II}	^SA-2	^2.4	²⁰		¹²⁵⁴	⁹¹⁰	¹⁵⁰⁰	⁵⁹⁰
^{SA-230A II}		^3.6	³⁰					⁶⁵⁰
^{SA-340A II}	^SA-3	^4.9	⁴⁰		¹³⁰⁰	¹¹⁴⁴	¹⁵⁹⁰	¹⁰²⁰
^{SA-340W II}					¹¹⁸⁰	¹³²⁰	¹⁵²⁰	⁹⁰⁰
^{SA-350A II}		^6.1	⁵⁰	^{220/ 380/ 440/ 3300}	¹³⁰⁰	¹¹⁴⁴	¹⁵⁹⁰	¹⁰⁵⁰
^{SA-350W II}					¹¹⁸⁰	¹³²⁰	¹⁵²⁰	⁹⁰⁰
^{SA-360A II}		^7.2	⁶⁰		¹⁶⁰⁰	¹³⁷⁰	¹⁴⁰⁰	¹⁰⁰⁰
^{SA-360W II}
^{SA-375A II}		^8.6	⁷⁵
^{SA-375W II}
^{SA-475W II}	^SA-4G	^10.5	⁷⁵		²⁰⁰⁰	¹⁴⁰⁰	¹⁷⁰⁰	²³⁰⁰
^{SA-4100W II}		¹⁴	¹⁰⁰					²⁵⁰⁰
^{SA-4125W II}		^16.5	¹²⁵					²⁸⁰⁰
^{SA-5150W II}	^SA-5	²¹	¹⁵⁰		²⁹¹⁶	²⁰⁰⁸	¹⁷⁰⁰	³⁵⁰⁰
^{SA-5175W II}	^SA-5G	²⁶	¹⁷⁵					⁴⁵⁰⁰
^{SA-5200W II}		²⁹	²⁰⁰
^{SA-5250W II}		³⁵	²⁵⁰		³⁰³⁶	²¹⁰⁶	²¹⁰⁶	⁵⁸⁰⁰
^{SA-5300W II}		⁴²	³⁰⁰
^{Note: 1. Working pressure @ 7 kg/cm²G}

　

Next Page